Scroll down

ZHH installs lightweight metal-framed partition walls, linings and plasterboard structures across the Netherlands. Standard CW and UW wall profiles are made of galvanised steel, not aluminium. We select the framing, insulation, boards and finish for each room.

Animation showing installation of metal studs, insulation and plasterboard.

Contact us directly

Do you have questions about a renovation, bathroom, roofing, electrical work or other building work? Message us on WhatsApp or give us a call.

Phone / WhatsApp: 06 4250 3008

ZHH Metal Stud partitions and plasterboard in the Netherlands

ZHH Zaag Hamer Huis B.V. installs lightweight metal-framed partitions, wall linings and plasterboard enclosures in the Netherlands. Standard CW and UW wall studs are galvanised steel, not aluminium.

We select materials for the space, planned services, insulation and finish. Acoustic, fire and strength performance depend on the full assembly; there is no universal rating for every wall.

You can enquire in English, Dutch or Polish. Include the location in the Netherlands, building type, approximate dimensions and photos or a floor plan if available.

What is Metal Stud construction?

Metal Stud is a lightweight partition system built from metal framing profiles and plasterboard. It is used for internal partition walls, wall linings and other interior structures. We select the profiles, boards, insulation and finish to match the room height, loads, services and project requirements.

Read moreCollapse article

Metal Stud, drywall and partition wall: what do these terms mean?

In the Netherlands, Metal Stud refers to lightweight steel framing finished with plasterboard. Terms such as drywall, plasterboard partition and metal-framed wall describe similar drylining construction, although the exact layers may differ.

A typical partition divides internal space and is not a load-bearing element. Unusual cases require checking the design and technical conditions.

Are Metal Stud profiles made of aluminium?

No. Standard CW and UW wall profiles are usually made from galvanised steel. Calling this type of framing “aluminium construction” is misleading.

When requesting work, specify a wall using metal studs and plasterboard so the intended system is clear.

What makes up the wall frame?

  • UW tracks fixed at floor and ceiling level.
  • CW vertical stud profiles forming the frame.
  • Suitable fixings, perimeter sealing tapes and any required reinforcements.
  • Plasterboard and, where specified, insulating infill.

Plasterboard partition walls

Metal Stud partitions divide rooms without heavy masonry. They are useful for home renovations, extra bedrooms, office layouts, attic conversions and changes to internal floor plans. We adapt the design to the wall’s intended purpose and building conditions.

Read moreCollapse article

Partition walls in homes and flats

Plasterboard partitions can create a bedroom, wardrobe, study or separate area without constructing a heavy masonry wall. They can also change the layout of offices and commercial premises.

Before installation, plan the wall position, doors, access to services and the room’s intended use.

One layer or several layers of plasterboard?

The board type and number of layers depend on the specified system. Additional layers may affect strength, acoustic performance and fixing capacity, but board count alone cannot guarantee a particular rating.

Doors, shelves and wall loads

  • Door openings may need purpose-designed studs and reinforcement.
  • Heavy cabinets, basins and shelves require planning and suitable support before the wall is closed.
  • Fixings must suit the board, frame and allowable system loads.

Wall linings and boxed-in structures

Metal frames and plasterboard can level uneven walls, conceal suitable services, make space for insulation and enclose technical components. These solutions are used in both older buildings and newly finished interiors.

Read moreCollapse article

Lining an existing wall

A wall lining stands in front of an existing wall. It can level surfaces, conceal selected cables, provide an insulation cavity and create a neat base for decoration.

Allow for the cavity depth, future access to services and moisture conditions behind the lining.

Boxing in pipes, risers and recesses

Metal studs and plasterboard can enclose services and technical features. Valves, inspection points and components needing maintenance must remain accessible rather than being permanently sealed behind the boards.

Attics and complex shapes

  • Check the condition of the substrate and how the framing will be anchored.
  • Account for slopes, recesses, movement joints and structural movement.
  • Choose a complete system suited to the intended finish.

Installing plasterboard

We install boards suited to the application, including standard, moisture-resistant, fire-resistant or impact-resistant boards and multilayer systems. All materials must meet the requirements of the complete construction system.

Read moreCollapse article

Which plasterboard should you choose?

Standard boards are common in dry rooms. Bathrooms and other damp environments require appropriately rated products and systems. Other boards offer specific fire, sound or impact resistance.

Choose the complete tested system based on its documentation, not simply the colour of a board.

Fixing boards and preparing joints

Boards are fastened to the prepared frame according to the manufacturer’s instructions. Joint layout, screw types, allowances and corner details all matter.

Poorly finished joints can crack. Correct taping, jointing and sanding are needed before painting.

Stages of finishing a plasterboard wall

  • Check the frame for stability and alignment.
  • Install the specified boards and finish openings.
  • Tape and fill joints, strengthen connections and finish corners.
  • Prepare the surface for primer, paint or other finishes.

Acoustic and thermal insulation

Insulation such as mineral wool may be installed between the studs. It can improve acoustic or thermal performance, but the result depends on the full assembly: framing, board type and layers, insulation, seals and workmanship.

Read moreCollapse article

What improves the sound insulation of a partition?

Performance depends not only on mineral wool but also on the number and type of boards, airtight joints and connections to floors, ceilings and adjacent walls.

Sound can travel through neighbouring building elements, so changing just one material cannot guarantee a specified rating.

Thermal insulation inside wall linings

Thermal insulation can be included in some linings. On external walls, moisture, airtightness and condensation risks must be assessed before the assembly is closed.

How can common mistakes be avoided?

  • Specify a compatible complete system rather than mixing unrelated components.
  • Seal perimeter joints correctly.
  • Avoid unsealed service penetrations and gaps.

Services inside Metal Stud walls

Metal Stud framing can accommodate electric cables and selected building services. Routes and openings should be planned before boarding the wall to prevent rework and protect the frame’s integrity.

Read moreCollapse article

Electrical cables in plasterboard walls

Some stud profiles include holes for cabling. Plan cable routes, boxes and protected penetrations before fixing the second board face. Qualified professionals should carry out and check electrical work.

Water services and technical enclosures

Not every pipe can be safely concealed in a thin partition. Allow for maintenance, pipe insulation, installation noise and moisture requirements. Size and build the enclosure for the services it contains.

Checks before closing the frame

  • Confirm cable and pipe routes and connection points.
  • Complete any required tests and take photographs.
  • Keep access panels and serviceable components reachable.

Metal Stud installation step by step

We begin with measurements and marking out the wall. Next we fit the profiles, plan services and insulation, attach plasterboard and finish joints. Finally, we check alignment, stability and readiness for decoration.

Read moreCollapse article

1. Measure and set out the wall

Measure the room, mark the partition position and assess the substrate. Plan doorways, necessary reinforcement and service runs at this stage.

2. Fit UW and CW profiles

Install tracks, studs and other specified components. Spacing, connections and perimeter seals must follow the system requirements. Add insulation and prepare services as needed.

3. Board, finish and inspect

After checking the frame and services, fix the plasterboard, joint the boards and finish corners. Inspect alignment and connections before decorating begins.

Where can Metal Stud walls be used?

The system is used in houses, flats, offices, shops and other commercial spaces. It is suitable for a single partition or a larger interior remodelling and renovation.

Read moreCollapse article

Partitions in apartments

Lightweight walls can create a work area or extra room during a renovation. Check the building’s requirements and existing services before starting.

Framing in houses and lofts

Metal studs can be used for wall linings, technical enclosures and interior partitions. Sloping ceilings, taller walls and uneven surfaces require a suitable installation method.

Offices and commercial units

  • Divide premises into offices and work zones.
  • Enclose selected pipes and technical equipment.
  • Specify acoustic, fire and durability performance suitable for the space.

Choosing the right wall system

Different walls need different stud and board specifications. Height, length, expected loads, moisture exposure, sound insulation, fire requirements and service routes all affect the choice. We assess the specific room and intended result.

Read moreCollapse article

Wall height, stud spacing and loading

A high partition or a wall carrying additional fixtures may need deeper studs or different spacing than a small domestic partition. There is no universal stud spacing for every project.

Moisture, acoustics and fire safety

Bathrooms, offices and areas with fire protection requirements may need different boards and complete systems. Check performance against the tested assembly, not one board or profile.

What information helps us choose the system?

  • Wall height, length and intended use.
  • Door openings, cabinets and expected loads.
  • Acoustic, moisture and any fire-safety requirements.
  • Photos of existing conditions and services.

Requesting a quote from ZHH

Please provide your town in the Netherlands, the building type and approximate wall lengths and heights. Tell us whether insulation, services and finishing are required. Photos or a simple floor plan help us assess the scope.

Read moreCollapse article

Dimensions and project location in the Netherlands

Include your town, building type and approximate wall length and height. Explain whether you need a new partition, wall lining, service enclosure or plasterboard fixed to an existing frame.

Photos, floor plan and desired outcome

Photos, a simple sketch and details of doors, services and planned fixings make the work easier to estimate. If you are unsure which materials are needed, describe your renovation goals rather than guessing.

What affects the price of a plasterboard partition?

  • Wall area, access and condition of the substrate.
  • Number of layers and board and insulation types.
  • Openings, reinforcements, services and finishing details.
  • Taping, sanding, painting and project schedule.

Frequently asked questions — FAQ

What is Metal Stud construction?

A lightweight internal framing system with metal profiles and plasterboard, used for partitions, linings and other interior structures.

Is a Metal Stud partition stable?

Yes, provided the profiles, spacing, boards and fixings are correctly specified for its height, purpose and expected loads.

Can Metal Stud partitions include insulation?

Yes. Insulation such as mineral wool can be installed between studs when required by the design.

Can cables and pipes run inside plasterboard walls?

Yes. Plan service routes and their protection before enclosing the frame with plasterboard.

Can Metal Stud be used in a bathroom?

Yes, with a suitable system and materials designed for higher-moisture environments.

Can a Metal Stud wall improve sound insulation?

Yes. Performance depends on the complete wall system, including framing, boards, insulation and connections.

Can Metal Stud walls be fire-resistant?

Yes. The required fire rating must be verified for the specific complete tested assembly.

How long does installation take?

It depends on the number and size of walls, services, insulation and finishing. A schedule can be agreed after reviewing the scope.

Request a renovation quote

Complete this short form and we will contact you to discuss scheduling and a quotation.

You do not need to know every detail yet. Enter the basics and we can discuss the rest by phone or WhatsApp.

You can contact us in English, Dutch or Polish.

1. Contact details
1. Contact details
2. Work location
2. Work location
3. Which services do you need a quote for? (select all that apply)
4. Current condition
4. Current condition
The property is:
Has the property been renovated before?
5. Floor area / scope
5. Floor area / scope
6. Timing and urgency
6. Timing and urgency
Is this urgent?
7. Photos (optional)

You can attach up to five photos. Another upload field will appear when you choose a file.

8. Additional details
8. Additional details
9. Preferred survey time (optional)
10. How did you hear about us? (optional)
11. Consent
11. Consent
Outline of a house
78 m²